In order to change the light light bulb on the car, you need to remember some of the rules. First of all, you can only install the license plate backlight, which is from behind. To do this, it is recommended to use LEDs with lenses, as they illuminate the number better and, according to the law, make it possible to more clearly see the license plate. Although there are lamps of various colors in a free sale, the law does not allow to apply many of them in practice.

For drivers

Replacing the light light bulbs are performed in the following sequence:

1. Thin screwdriver need to disassemble the ceiling, starting from the middle.
2. Carefully unscrew the regular lamps, as it is quite easy to damage the holder on the body.
3. The next step is installed LED or incandescent lamps.
4. Before installing in its place, the plastic should be deguted.
5. After installing the ceiling, you should check the operation if the rear number of the backlight light is performed exactly, then the number will be brightly lit.

When replacing the backlight on different models of cars, there are small nuances that differ during installation. So that the work was performed correctly, such differences should be taken into account.

Holding work with Hendai-Solaris

The license plate lights two lamps, which are located on the lid of the trunk under the lining, they are interrelated among themselves. In order to be replaced by the illumination light bulb, Hyundai-Solaris number, you must remove the upholstery from the trunk lid, for this:

1. Wear a screwdriver cover in a handle that closes the trunk.
2. Despite the resistance provided by the clamps, open the lid.
3. Using a cruciform screwdriver, unscrew both self-buildings that fasten the handle, remove it.
4. Using the same screwdriver, unscrew the pistons that fasten the upholstery in the lid of the trunk, and extract them, after which the upholstery is removed.
5. It is necessary clockwise to rotate the cartridge before the stop and, together with the lamp, remove it from the lamp body, the wires are needed to pull it into such a length so that it is convenient to change the lamp.
6. To remove the lamp from the cartridge, it is enough to pull it over the flask.

To replace the Handai-Solaris Light Bulb, it was performed correctly, the entire installation of lamps and parts is necessary in strictly reverse order.

After completion, it is necessary to check the assembled equipment. When compliance with all conditions and requirements, the backlight should work smoothly, only after this replacing the light bulbs of the Solyaris number will independently be considered a qualitatively conducted.

Replacement on "Prior"

It is also not difficult to make such a job on the "Prior", it is fairly accurate to follow the instructions and have the necessary tool. First of all, the end keys will be needed:

• With the help of keys, it is necessary to remove the plastic attached to eight hedgehogs.
• To remove the rear chrome frame over the number you need to unscrew all four nuts. Lamps installed in the frame.
• In order to get light bulbs installed in the ceiling, you need to apply a little effort, since they are hard to disassemble.
• When opening a ceiling, it is important not to lose sealing gum. Replacing light bulbs The "Priora" number is performed quickly.

It is necessary to check the operation of the installed light bulbs before assembly, so as not to be re-work. The reverse assembly process occurs in accurately with its disassembly. After replacing the lamps, plafones are installed, then the frame is set to its place, which is fixed by bolts. After that, plastic removed on the previous place. On this, the replacement of the light light bulbs is considered to be finished.

Replacement process on Kalina

Over time, on any car, it is required to replace the wear parts, is not an exception and "Kalina". If the license plate has become poorly or unevenly covered, the lighting light bulb is replaced by the "Kalina" number. It is easy to do it yourself:

1. For greater convenience, it is worth opening the trunk of a car, removing the ceiling.
2. To remove the ceiling, a thin screwdriver needs to be pressed on it from the left side to its displacement to the right and squeeze.
3. Gently, not to break, lifting the latch up, with a screwdriver, you need to remove the flashlight.
4. We raise the plastic lock up and remove the power plug.
5. After that, we take out the base with the light bulb, turning the white housing counterclockwise.
6. Remove the light bulb from the base, with a slight movement pulling it to the side.
7. After replacing the lamp, all the work is done in the reverse order.

Replacing the light light bulbs does not require special skills, attention is necessary, patience and desire to produce it independently. Many Kalina owners often face this problem, its decision will not take much time and does not require the intervention of specialists.

Illumination of the number on "Casca"

Replacing the lighting light bulbs Number of Cascai is not particularly different from this procedure in other cars, there are only small nuances that should be followed. First of all, before repairing, you need to disconnect from the battery "minus" cable. Next, it is necessary to make the following actions:

1. With a screwdriver, remove the rear license plate lighting plander. To do this, you need to push it right on it and pull out.
2. Gently remove the cover of the ceiling.
3. Disconnect the connector.
4. To pull the lamp, you need to turn the cartridge counterclockwise.

After an easy procedure, a new light is made and an assembly is made in the reverse order. After installing a minus cable, you need to check the operation of the number illumination. Replacing the number light bulbs with their own hands will save not only time, but also tools.

DIY repair on Renault Logan

The backlight of the rear room is required at night to determine the vehicle. Therefore, during its breakdown, it is necessary to replace the light light bulbs that it is easy to produce on its own. For Renault Logan, as for many other car models, incandescent lamps and LED lamps are suitable. The first does not have great reliability and low energy consumption, but due to low prices are in demand. The second possess large brightness and use little energy, but their cost is significantly higher.

Replacing the light bulb number on Renault Logan will not take much time:

1. You must disconnect the "minus" wire from the battery terminal.
2. Click on the retainer and remove the lighting lantern of the license plate from the groove of the rear bumper.
3. Press the lock and remove the dispersion of the lantern.
4. Extract a lamp a lamp that does not have a base.
5. Install a new lamp and collect all the details in the reverse order.

An independent installation will not take much time and will help you quickly correct the breakdown.

Backlight on "Toyota Corolla"

If you need to replace the backlight of the rear number on the Corrupt car, you need to make simple actions.

1. Press the tongue and lower the dispersion of the lantern down to get easy access to the spoiled light bulb.
2. Then counterclockwise turn the bulb cartridge, then remove it.
3. Then unscrew the screws on which the lantern of the license plate and completely omit the flashlight.
4. Next, remove the bulb holder, for this you need to turn it counterclockwise.
5. Recently get a light bulb from the cartridge.

When the illumination light bulb is replaced, the assembly is made in the reverse order. Such a job can perform every driver yourself.

Rear Number Backlight

According to the rules of the road, at the occurrence of twilight, the rear license plate should be highlighted with yellowish or white light. This will not only help determine if necessary, the vehicle number, but also shows its direction of movement. If the license plate is shining in blue or red or bright LEDs, it can provoke an emergency. Since at night, the perception of the driver moving from behind may change.

Work for specialists

Not all drivers, encountered with the problem of the burnt light bulb on the back of the rear number, are trying to do work independently. Sometimes an obstacle can be the need to remove the sheath inside the trunk or removal of plastic rivets - many are afraid to break them. It is not always possible to remove the plastic, or are rather short wires and get to the bulb is almost impossible. In such cases, it is better to turn to professionals.

The lamps responsible for providing the highlighting of the registration number in the Renault Logan model family are capable of quite infrequently disturbing the owner with its way out. Burns such an element about 1-1.5 years. The process of replacing the lamp is quite simple, so I can cope with such a "task" by even a considerable car enthusiast.

Using the instructions below for Renault Logan, the light illumination light is replaced within 15-20 minutes.

What types of lamps are suitable for highlighting the number in Logan?

These elements are similar as the highlighting lamp of the room used for the overall lights of Renault Logan, and have a "12V W5W" label. Even such lighting devices can be detected in the cabin light in the ceiling and the glue node of the glove box.

If you need to replace the number light bulb, then you can purchase "W5W" elements in any trading specialized network. Their cost varies depending on the degree of "cattleness" of the manufacturer and the quality condition of the product itself.

We present prices for some options of the 12V W5W lamps, for Renault Logan per unit:

• "Koito" (1583) - 25 rubles. and higher;
• "Philips" (P-12961) - start from 30 rubles;
• Bosch: Model "PURE LIGHT" (1987302206) - 25 rubles. and more;
• «OSRAM» (O-2825) - from 20 rubles.
• "Philips": Modification "Longlife Eco Vision" with an increased resource - from 45 rubles;
• "OSRAM": the Ultra Life version, which also owns a longer service life - the most expensive, from 50 rubles.

When choosing an option, we recommend refusing to consider the cheap (mainly Chinese) instances with dubious quality for Renault Logan. Their resource is not great, and without a characteristic darkening, do not do, which will make the backlight of the room very dim. To guarantee an increased service life of this element, it is recommended to bow down to the acquisition of resource-intensive and high-quality lamps, labeled as such:

• "Longlife Eco Vision";
• "Ultra Life".

If you do not please the incandescent lighting lamp, we recommend choosing the LED analogue of identical parameters ("12V W5W"). They are closer to white, and the effectiveness of light output is significantly better. Note that the resource of diode versions is much higher than that of the "outdated" elements with incandescent thread.

How to replace the lamp?

Replacing the light light bulb is an absolutely not complicated procedure.

• Taking advantage of a thin screwdriver having a flat tip, gently press the fixing element of the ceiling and remove the last outward.
• When the cartridge is completely removed from the landing jack in the rear bumper Renault Logan, turn off the connector of its power.
• By clicking on the locks, carefully get the transparent diffuser.
• We remove the old lamp, instead of which we install a new analog.

Before directly executing the replacement procedure, turn on the backlight mode, only after that begin the specified manipulations. LEDs have polarity, so if they did not earn after installation, they simply turn over (180 degrees) of them - the instruments must "come."

When only one lamp of the backlight lamp came into disrepair, we recommend not to neglect the second test. If the working surface of the last handled, it is better to replace it in advance, because the "solemn" brave is about to take place.

To ensure a long-term resource, purchase only high-quality elements with elevated conditioned or diode versions. The Renault plant resorts to the installation of lamps, kindly provided by the brand "OSRAM".

If a malfunction itself was a malfunction (the scattering surface burst or crackled), then it can be purchased by ordering on the original code 8200480127 from the Renault-Nissan manufacturer.

The backlight of the license plate, which is a mandatory attribute of cars, often causes drivers questions related to possible changes or upgrades in its installation. So, according to GOST, you need to adhere to lighting the number sign of the back of the machine, while avoiding the backlight of the front number.

If the light over the "mini-passport" car does not burn, or the lighting does not comply with the standards, the driver of the vehicle when the traffic police inspectors are detected by the government's penalty. To avoid punishments, you should be fully aware of how to properly install and operate the lighting device.

Regulatory and legal aspects

The rules of the road rules states that each car must be equipped with special lighting equipment for the rear of the car capable of turning on during the operation of the overall lights. It is necessary to activate it, respectively, in the dark time in order for the traffic police inspector without effort to distinguish the "mini-passport" symbols of the vehicle from a distance of at least 20 meters.

The penalty for the lack of backlighting the rear number and, accordingly, its delictitude is 500 rubles.

The ability to lose the driver's license for a period of 6-12 months with confiscation of the lighting device is also present. Such a punishment may be subjected to the vehicle owner for coverage of the front registration license plate, since it should be absent according to regulatory documents.

Improving lighting

The illumination of the room is not a problem, it is possible to introduce it through the modernization of regular lanterns. Today, the LEDs are most often installed in the form of ribbons, lines and modules. However, brute force with the number of LED items may be regarded as a change in the car design.

To avoid punishment, you should remember two things:

• First, the violation in the coverage of the state registration number can be proved only if the vehicle is in operation.
• Secondly, the changes that have passed the certification of the traffic police cannot be considered illegal.

On the intensity of burning backlight and allowed LED colors

According to GOST, the light of the rear registration signs should be white or yellow color, or their shades. Thus, any other color of lighting can be regarded as a violation and enforced by the corresponding fine of 3000 rubles, since color LEDs can confuse drivers traveling and provoke a traffic accident (accidents).

Taking into account standards, changing the tonality and saturation of the lighting. However, it is necessary to do this without the attention of the inspector to the inspector too bright light leaving the trail on the roadbed, as well as the use of excessive lighting of the number of other colors.

Attributes of lighting upgrade

The illumination of the spiral number used in the factory lights can be replaced with similar LED bulbs of a more powerful spectrum. The LED sizer for a light bulb with a standard base is from SMD5050 to COB matrices. The main positive quality of such light bulbs is compatibility with an on-board computer (BC), that is, it will not give an error when installing LEDs. Prices of lamps depend both on the desired power and from the manufacturer. On average, a set of LED devices from two lamps can be purchased within 300-400 rubles.

Behind the backlight of the registration symbols by the LED module, the owner of the vehicle will have to pay at least 600-800 rubles. But the advantage of such a LED appliance also has: their geometric dimensions are exactly repeated by standard ceilphones, i.e. No need to redo fasteners.

A budget way to solve a license plate illumination problem is the ability to glue the LED tape over the number or around the perimeter. It is important to remember that it is possible to glue it only on the place of purified from dirt and oil, otherwise, the durability of the tape is not guaranteed.

In conclusion, I would like to say that it is necessary to strictly adhere to the rules of operation of the car, it properly refers to the lighting devices of the car. Always before departure, check the help of headlights to function as the backlight backlight and the front - this will provide easy readability of numbers. Take advantage of measures to eliminate any problems.

What is this service?

Many drivers probably already had such a problem as replacing the Loading Lamp Lampor . The difficulties in this not very difficult procedure begin immediately from questions: what light bulb should I buy and what is the fair price? The answer may be different. If the light bulb served you faithfully for a long time and failed after its expiration of its operation, then you can trust the same model, pre-twisted it and showing the seller in the store. Although, as experience shows, in a few years, namely, this is the normal life of the lamp, you will no longer find a similar model. In this case, it is better to entrust the work of professionals. They will offer several different, in the price range of options, and you already choose the most suitable.

Replacing the license plate lamps usually begins with removing the fastening from the lining of the lock and from the pad on the trunk lid. Then the right or left cartridge is retrieved, and from it - a blown light bulb. This procedure ends with its replacement and performing installation work in the reverse order.

Keep in mind

what replacing the license plate lighting lamp Usually does not flow smoothly as the textbook. As practice shows, often accompanied by many additional problems. The lamp is often tightly soldered by the basement to the cartridge, and the locks that hold it are usually made of plastic and have a very fragile structure. To unscrew the cartridge from the ceiling also turns out to be as simple as it will seem first.

Stay your choice on the most modern and reliable lamps, such as LED. Their cost is though higher, but the life and brightness of the lighting is justified.

How important is it

If you have no time to change the lamps yourself, and it's just no time to go to the service, then you can get such a service in any place convenient for you. Our specialist you can choose yourself will come to your home, to the office, to the parking lot and will work with a guarantee of quality.