Even the most careful drivers sometimes find themselves in unpleasant situations. If you bumped into a post while driving out of a grocery store parking lot in reverse, someone parked too close to your car and banged the door on it, that doesn't change the fact that you end up with an unsightly dent. Very often, repairs to such minor or more than minor damage are easily covered by the warranty, but nevertheless cost more than you are willing to pay out of your own pocket. In many cases, it is possible to remove a dent without the help of a workshop technician.

For repairs, you can use the tools at hand, such as a regular hairdryer, compressed air can, plunger or suction cups. In this article we will analyze 2 main ways body repair and minor damage.

Using a hair dryer to pull out damage

Of course, with just a hairdryer and a few other tools on hand, you can't put up a bodybuilder's sign at the entrance, but trying to do the repair yourself can save you an impressive amount of money. The principle is quite simple: a hair dryer produces heat, and at a certain temperature, the metal, as you know, becomes malleable. This means that metal, including metal body components, can be shaped, provided it is sufficiently heated.

Item 1 of 3: Assessing the nature of the damage

It is quite obvious that repairing dents when using a hair dryer on a car in a serious accident is useless, but it makes sense in the case of small deflections and indentations in certain areas of the car body. To determine if a particular dent is to be repaired in this way, it is first necessary to analyze its location.

Step 1: analyze the location of the dent. It is easy enough to remove dents on smooth surfaces such as the trunk or hood lid, roof, doors and fenders. It is much more difficult, but possible, to deal with dents in curved and embossed areas.

Step 2: determine the size and depth of the dent. If the dent is three inches or more in diameter and is therefore shallow, and there is no obvious sign of paint damage, you will most likely be able to remove the dent without any problems.

In fact, there are two ways to remove dents with a hair dryer. In the first case, compressed air is used in combination with the heat produced by a hairdryer, in the second - dry ice. Both of these methods of repairing dents are quite effective, but for many, the one that uses compressed air rather than dry ice is preferred. In addition, in some regions it may be difficult to obtain dry ice. In any case, when performing work of such a plan, protective gloves should be used, preferably rubber coated insulating gloves.

Step 2 of 3: compressed air

Necessary materials:

* Clean soft cloth;

* A can of compressed air;

* Heavy duty rubber coated insulating gloves.

Procedure:

1. Providing free access to the area with a dent. If possible, provide free access to the dent on both sides. For example, if the dent is on the bonnet, open the bonnet.

2. Heating the area with a dent. Turn on the hair dryer, set it to medium power, and blow air over the dent, keeping the hair dryer 5-7 inches away from it. Depending on the size of the dent, you can move the hair dryer back and forth or up and down to warm up the area more thoroughly.

3. Determination of the degree of malleability of the metal. After two minutes of heating the surface, put on gloves and check the degree of pliability of the metal by gently pressing on the dent from the inside or along its outer edge. Having felt a certain softness of the metal, you can proceed to the next step of the procedure. Otherwise, heat the surface additionally for a minute and check the degree of metal compliance again.

4. Impact on the dent with a jet of compressed air. Shake the can with compressed air and direct the air stream to the dent, holding the can upside down, remember to first wear heavy-duty protective gloves. Continue to spray air on the dent until the metal straightens out (usually 30-50 seconds is enough).

5. Cleaning. Using a clean, soft cloth, gently wipe off any remaining liquid from the treated surface.

Step 3 of 3: dry ice

Necessary materials:

* Aluminium foil;

* Pack of dry ice;

* Heavy-duty rubber coated insulating gloves;

* Insulating tape.

Step 1: heating the area with a dent. As in the previous procedure, it is advisable to provide access to the dent from both sides and heat the area with the dent with a hairdryer until it is possible to give the metal its original shape.

Step 2: positioning the aluminum foil over the dent. Cover the dent with a piece of aluminum foil, securing the corners with duct tape. This will prevent dry ice from damaging the paintwork.

Step 3: application of dry ice. With heavy-duty gloves protecting your hands, place a bag of dry ice and run it over the aluminum foil until you hear a characteristic pop. This step usually takes less than one minute.

Step 4: cleaning. Remove the aluminum foil and discard.

Many people understand the purpose of using a hair dryer - to soften the metal in the dent area to straighten it, but some do not immediately understand how compressed air or dry ice affects the metal. Both of these products have a very low temperature, therefore, after heating the metal with a hair dryer and, accordingly, its expansion under the influence of heat, a sharp change in temperature downward causes the metal to shrink and return to its original shape.

* Recommendation. If, as a result of using one of the described repair methods, the dent has become significantly smaller, but the surface is not completely flat, you can repeat the procedure. Wait at least one day before repeating this procedure. This is due to the fact that sudden changes in temperature to which the area with a dent is exposed can damage the paintwork of the car.

Using a suction cup or plunger

The technology of this method is very simple and it makes no sense to examine it thoroughly. Using a suction cup, you can remove a dent in a short time and without much difficulty without painting the car.

To repair a damaged area, you may need:

A plunger or suction cup.

Detergent for cleaning the surface.

LDS or bright lantern.

Gloves.

The procedure is best carried out in a bright room, so that the metal bend area is clearly visible without additional equipment. If this is not possible, then you can use a bright flashlight. When illuminating irregularities on the body, roughness will be visible, visible to any eye.

Procedure:

1. Thoroughly clean the damaged area of \u200b\u200bthe body from dust and dirt. Wash the part and dry the dent stain well.

2. Secure the plunger in place of the dent. For better contact with metal, you must use a soft rubber suction cup and preferably at a warm air temperature.

3. Pull the plunger back vigorously. It is important to calculate a force commensurate with the pulling out of the dent. If the force is large, an external "bubble" may form on the body, which will already be much more difficult to remove.

4. If the first time, it was not possible to fully extend the concavity, the procedure can be repeated until the desired result is achieved.

* This method is very suitable for removing small dents, with even stretching of the metal, mainly in a round shape. The use of household suction cups is suitable for this method in the same way as a plunger. It will be important to take into account the ratio of the diameter of the area of \u200b\u200bthe sucker to the area of \u200b\u200bdamage; these surfaces should be as proportional as possible.

The average cost of repairing a dent on a car, even a small car, is a considerable one. Of course, repairing large damage would cost you even more. So, who would think that a pot of boiling water and a little effort can do the same job?

This surprisingly simple solution is enough to drive any mechanic crazy. You can save hundreds of dollars by simply walking into the kitchen, heating up boiling water and using it to pop out the dents.

The warmth of the water is what makes the material of the car more flexible, allowing you to change it. You just need to work quickly because the heat won't last very long and you need to keep boiling water at 100 degrees until you're done. What's more, boiling water doesn't destroy car paints, making this one of the most amazing, fast and easy-to-maintain cars in the repair shop. Still can't believe it?

Using boiling water to remove car dents - from TeamFamily.

All you need is a huge pot of boiling water and neatness, care. If you wish, you can also use gloves to avoid burns. Pour boiling water over the dent and, at the same time, push the inside out and pull it out. Alternatively, you can use a suction cup to remove the dent. Many thanks to the creator of the video "TeamFamily".

Heard about this advice and thought I would give it a chance. It really works with little effort. Try it. This will not work for ALL dents on ALL cars. You can never suck in a huge dent in the bumper or a tiny pea-sized one on the roof.

Removing extreme large dents with a simple DIY technique

There is nothing more awkward than a dent on the body of your car. It looks disgusting, but is there a simple and cheap solution that will make this dent a thing of the past?

Yes, you will get the right solution in this video to help with giant dents. It doesn't matter what size, as long as you follow the video step by step.

it's all about getting your best foot forward with the tips provided in this video.

Extreme removal from F1Dents. Special thanks to the presenter of the video "F1Dents".

Keep your car like new!

A smart life hack to repair deep scratches on your car paint.

Scratches on car paint can occur for a variety of reasons. Your car can get deep scratches from a simple bush, a collision with a street object, or metal objects that you put on the surface. Even the simple act of removing bird droppings with paint using a paper towel can lead to scratches. Usually, if the scratch is too small to require repainting, you just wipe it off and hope no one notices.

However, if the scratch is left unattended or not repaired, it may deteriorate over time because the scratches and chips may become clogged with dirt and the cracks will penetrate deeper. Fortunately, there is a way to repair and minimize deep scratches without having to repaint your vehicle, which will cost you a lot of money and time.

This simple life hack involves the wet sanding and polishing process, as well as using simple hand tools found in your garage or workshop. To learn how to repair scratches and what you need to use, just watch the video tutorial.

How to Repair DEEP Scratches - by "milanmastracci". With this scratch fix, you won't have to endure scratches or take your car to services for costly scratch repairs or repainting jobs. You only need the right tools and make sure you follow the instructions and advice to safely perform this method. Also, make sure you apply paint protection or paint sealants to the affected part to protect it from external elements. Many thanks to the creator of the video "milanmastracci".

Because the main deep scratch goes through the clear coat and base coat, I can't remove the scratch without cutting too deep into the paint, so I can't fix it completely. You can see how I look much better than before. Now all small scratches that were around the large scratch have been completely removed by following this procedure ... milanmastracci

Thanks for watching.

The sparkling body of a vehicle is a reason for pride for every motorist, so when the slightest defects are found, the question arises of how to remove a dent on the car. A minor accident (traffic accident), an accidental door bump of an unsuccessfully parked car nearby, children's ball games and even fruit falling from a tree can lead to dents. The insurance benefits cover some of the costs, but the cost of body repair is much higher. You can also do it yourself without painting a dent on a car, taking into account the recommendations of specialists.

In order to remove an insignificant dent from a door, hood or roof of a car, you should arm yourself with a device that delivers a strong stream of hot air, a compressed air cylinder and soft textiles. If the above is not at hand, it is allowed to replace the building hair dryer with household one, and compressed air - with dry ice.

The method is based on the principle of changing the physical properties of a metal when exposed to elevated temperatures. Before handling, it is recommended to equip yourself with protective equipment such as heavy-duty protective gloves and assess the size and location of the defect. If the car is damaged in a serious accident, it will be irrational to remove the dent with your own hands.

• the surface is thoroughly cleaned of dirt and dust, degreasers are used;
• for optimal results, it is recommended to provide free access to both sides of the damaged area;
• a stream of hot air is directed to the place where the dent is located, the holding time is 2-3 minutes;
• one of the most important steps is to determine the pliability of the metal, for this, the bulge or its edges are pressed to determine the degree of softness. It is important to remember that this action is performed only with heavy-duty gloves;
• if the metal is malleable enough, a jet of compressed air is directed at it until the dent is straightened.

The same procedure applies when using dry ice. The difference between the methods is that a sheet of aluminum foil is laid between the paintwork and the package with solid carbon dioxide.

When deciding how to remove such damage on a car without painting, you can pay attention to such a device as a plunger. When choosing a fixture, it is important to consider that the diameter of the suction cup should correspond to the size of the dent. In addition, the room in which the manipulations are carried out must have good lighting and heating. In order for the plunger to fit as tightly as possible to the metal, its suction cup must be made of soft rubber.

The device is applied to the dent and pulled with a carefully calibrated effort. If the movement is too sharp, a bulge may form on the surface of the body, which will require the help of specialists to eliminate it.

1. The glue is heated with a special gun and applied to the surface of the suction cup.
2. Place the device on the dent and wait for the glue to dry.
3. Using the bolts located on a special bridge, pull out the dent until the defect is completely eliminated.
4. Remove adhesive residues from the paintwork with a spatula.

Thus, you can protect not only the car body, but its coating. This method is used to correct any irregularities found on the vehicle.

If the defect is deep enough or has sharp edges, it is allowed to use a conventional hammer and mallet. It should be remembered that for the following manipulations it is necessary to provide full access to the dent. If damage is found on the car door, it should be dismantled and the trim removed.

The convex side of the dent is leveled with light blows from a rubber-headed hammer. Pay attention to the force of impacts, as the paintwork can crack and peel off. In this case, after eliminating the defect, the body will have to be putty, primed and restored.

If using a mallet is ineffective, place a piece of wood wrapped in fabric on the convex part of the dent.

In this case, the alternate blows of the rubber and metal hammer should fall on the block.

You can observe situations when a dent can be removed only by straightening. To do the work yourself, it is worth preparing special equipment. However, specific skills are required to complete the work, so it makes sense to contact specialists.

Both a beginner and a fairly experienced driver at least once during driving was interested in the question of how to quickly and easily remove a dent on your favorite car. Especially if the damage is small, you can do it yourself.

To solve the problem on your own, you need to pay attention to a number of points.

Determine the degree of damage

To know exactly when you need professional help and when you can handle it alone, you should pay attention to the depth and size of the defect.
A deep dent is considered to be one with a thickness of 10 mm or more. Serious damage suggests that you will not be able to cope with the problem on your own. It is worth seeking professional help.

Minor damages have a depth of up to 5 mm, it will be quite easy for even an inexperienced driver to cope with such damage.

How to fix the problem yourself

There are several ways you can easily deal with a dent on your own. Using improvised means will help you forget about the problem forever:

It should be understood that independent measures can have a rather unexpected effect. It is possible that the paint will burst or a scratch will form during the repair process.