How to tint a car? This is a question that deserves special attention. The appearance of a vehicle with a good design and amazing tuning is what attracts the eyes of everyone around. Toning refers to tuning elements. It is worth considering in more detail the question of how to tint a car, because thanks to tinting, the car will acquire charm, shine and presentability.

The tint film, among other things, prevents many unpleasant effects on the car. Among them are the burnout of the trim, dashboard, acoustics and audio equipment. In addition, the tinting will create a barrier that prevents the sun from blinding the driver.

When tinting with a film, car windows are not dismantled. Maybe only the door panels are removed - and that is very rare. It is also a very fast process: the car can be completely tinted in three hours. This does not scratch the glass. Another plus that a tint film for a car has - it can be removed at any time, and the glass will remain intact. It is also heat-resistant: it is not afraid of overheating or frost. It does not shine, demetallize, flake or bubble. Plus she doesn't miss

How to tint a car with your own hands? Not as difficult as it might seem. This will require an eraser spatula, shampoo, knife, blade, ruler, and tape.

How to tint a car correctly? First, you need to wash it thoroughly, washing off all the fat from the glasses. If you do not do it efficiently, then hairs, dust particles will clog under the film, and this is fraught with a bad result. Then you need to measure the glass (a allowance of five centimeters is taken into account on each side), and you can proceed to the film, or rather, to cut it. Find the transparent side of the film. Then you should take the film and sprinkle it abundantly with water, in which there is a sufficient amount of shampoo. The film must be damp, even wet. Then it is divided to the end (you need to make sure that its sides do not stick together), and the transparent part is thrown away. The adhesive side of the film is applied to the car glass. Then you need a rubber eraser, which will need to drive the water to the edges from the center. The film must be held so that it does not slip. Attention! You need to remove ALL water. Then, after an hour, you can cut the film. But by no means exactly on the edge - for this you need to wait about 8 hours. You can dry the film with a hairdryer to improve the result.

How to tint a car, or rather, its rear window? The film is attached to it in a different way. You must first carefully examine it, then wash it thoroughly. Fastening starts from the top. The washing liquid must be distributed over the top of the already washed glass. Then 1/3 of the film is separated and the liquid is abundantly sprayed onto its surface. The same operation will need to be repeated with the remaining 2/3 of the film. As already mentioned, you will need to wait a few hours, after which it will be possible to adjust. And finally, advice: for the first 2-3 days, you do not need to open windows in order to avoid possible deformation (this is if the film is not of the highest quality).

Do not forget that even such work as tinting a car on your own must be carried out with the utmost diligence so as not to miss any trifles.

If the car glass is damaged, then it cannot be tinted. Minor scratches are an exception. If we are talking about significant damage (cobwebs, round holes, etc.), then first you need to repair or completely replace the glass. It should also be noted that it is better to carry out work on car tinting with an assistant. This will save you a lot of time and effort.

Any window tinting always starts with side windows, because they are the easiest to dismantle.

Materials and tools for car tinting:

• Detergent.
• A sharp blade or utility knife.
• Rubber spatula.
• Tinting film for glass.
• Spray bottle.
• Warm water.
• Lint-free napkin.

All of the above materials with tools must be prepared before starting the tinting work on your car.

Phased work:

Stage 1

Glass tinting must be started after washing. Thoroughly rinse the glasses from dust and dirt, and on both sides. Make a soapy solution, apply it to the glass surface, and then wipe dry with a lint-free cloth. Use a utility knife or a sharp blade to check if any fluff remains on the glass.

Washing glasses with soapy water

Stage number 2

We prepare a special solution, necessary for the application and further fixing of the tint film on the glass. Dilute shampoo or some kind of detergent in warm water. Beat until foam appears. The foam will allow the film to slide over the glass, which will make it possible to make the final fit. For convenience, the prepared solution can be poured into a spray bottle. That's all the preparation for glass tinting. Next, you will need to work closely with the tint film.

Preparing a soap solution

Stage 3

Car glass measurement

Exactly measure the length and width of the windows that are going to be tinted, and only then, strictly according to the obtained parameters, cut out the tint film.

The pattern can also be obtained in another way without measuring the parameters of the glass. A film is applied to the glass from the outside of the door and smoothed well, and then simply cut along the contour.

Film pattern on car glass

An important point! The sides and bottoms should be cut first. There is no need to rush in this work. Tinting should be done without any tiny gaps. The top side of the film should be cut after it has been moved down by 5-7 cm. The main thing here is high accuracy and accuracy.

Stage 4

When the film is completely cut to size, the glass is only half tinted. Now is the time to apply it to the glass. By the way, you can use scotch tape to effectively separate the film into two parts. This is done very simply: adhesive tape is glued to the film on both sides at different levels, and then you need to pull it in different directions. Next, we put a film on the soapy glass and move it as needed so that it ultimately fits perfectly.

The process of separating the film from the substrate

Stage 5

Now it is very important to gently smooth out the film with a rubber spatula and expel air bubbles and soapy water from under it. Further, in parts, the protective layer of the film should be removed. It is necessary so that you can stick well and smooth the film.

Smoothing the film with a squeegee

Stage 6

After tinting the side windows, proceed to tint the rear window. That is why they first undergo training on the side windows. The fact is that all rear windows are curved, and this significantly complicates the whole process of work. Nevertheless, in general, the entire rear window tinting will not differ much from the side window tinting.

Car Rear Window Film Application Process

Important! The film must be glued strictly from top to bottom.

Carefully separate from the glass, first only the third part. Then this surface must be well lubricated with soapy water. Then fix the film on the glass and you will need to separate another third of the tinting from the protective layer.

Smoothing the rear window should be done with extreme care so that no air or soap solution is left anywhere. The glass will dry for 3 days (during this period it is not recommended to touch it with your hands).

Tinting with an industrial hair dryer:

It is worth noting that tinting the glass on your own, even with a partner, can cause some difficulties on the windshield and rear window, since they have a blown shape. An industrial hairdryer will help you out here.

It is necessary to carefully stretch the film over the entire area on the moistened concave glass without removing the protective layer of the tint film. When gluing the film, use an industrial hairdryer to remove any excess soap solution and air bubbles. This happens due to the heating of problem areas of the film.

Self-tuning a car requires certain skills and abilities. Effective mastering of them allows you to successfully cope with the task on your own, without the help of specialized services. One of the common types of modern tuning is car glass tinting.

Most car enthusiasts tend to believe that such transformations help make the car more attractive and contribute to the creation of a comfortable zone of personal space.

Car glass tinting is a rather laborious process, as it might seem at first glance. But, in fairness, it is worth saying that such an impression is formed only by those who do not have an idea of \u200b\u200ball the nuances of this process.

The lack of comprehensive information on a given topic deprives car owners of the opportunity to fully familiarize themselves with the presented issue. That is why, for the implementation of such tasks, most of the motorists turn to specialists for help. The presented article is intended to help motorists in mastering the basic skills of car tinting.

Requirements for window tinting according to legislation

Despite the widespread use of this type of tuning, it must be remembered that currently there are a number of restrictions and prohibitions within the framework of the presented question.

In order not to become a victim of such circumstances and not to attract the attention of traffic police inspectors, it is necessary to adhere to certain standards provided for by law. It's no secret that such violations are punishable by a fine of 500 rubles or more.

So, the first thing you should pay attention to is the light transmission capacity of the tint film. In the case of windshields and side windows that provide driver visibility, the throughput factor should be not less than 70%.

Particular attention should be paid to the characteristics of the light protection strip located at the top of the windshield. It also has certain requirements.

Its width should not exceed a value equal to 140 mm... It should be noted that the normative acts do not say anything about the degree of darkening of such a strip.

The above requirements do not apply to rear windows.

Among all other types of tinting, the so-called mirror film is especially popular. In this case, it is difficult to refer to any specific document prohibiting its use.

The traffic police inspector has no right to make any claims about this, for the simple reason that he does not have special means at his disposal to determine the specularity of the film. One way or another, in order to avoid controversial points and unnecessary problems, it is recommended to limit its use on the front side windows and on the windshields.

Which film is better to choose for self-pasting

At the initial preparatory stage of car tinting, it is important to decide on the choice of material. If you are new to this business, this aspect becomes much more important.

Let's start with the fact that today the car enthusiast has a wide selection of models and types of tint films. Let's get acquainted with the most common ones.

These include:

• painted;
• metallized;
• with a transition;
• energy saving.

These are not all types of films that are presented in the automotive market, but the choice of these is the most justified for those who first decided to try themselves in this business.

Dyed types of films are in demand largely due to the optimal price-quality ratio. Nevertheless, despite all the advantages of such a film, it also has a significant drawback. The fact is that over time, the film, under the influence of solar radiation, simply loses its attractiveness and ceases to please its owner.

Another type is metallized films. Such a film is practically not subject to fading. Looks pretty impressive and properly provides sun protection.

The film with the transition is significantly higher in price than conventional counterparts. The title of the film speaks for itself. It is enough to look at it, and it becomes clear how it differs from all the others: the layer of metallized spraying changes its density increasing from the lower base of the glass to the upper one.

It is worth mentioning the energy-saving types of coatings. The film has good protective properties and helps the driver and passengers get rid of intrusive glare and sun rays. It should be noted that due to their high cost, the demand for them is somewhat lower than for all other types.

Preparing to work with a car

Before you go headlong into the process of tinting a car, you need to thoroughly approach the issue of preparatory work. It is important to remember that the success of the entire event as a whole depends on the thoroughness of the implementation of all preliminary actions.

In this case, it will be appropriate to follow the step-by-step instructions. This approach will allow you to take into account all the nuances of the upcoming process and save you from unforeseen situations.

How to calculate how much material is needed

First of all, what you should pay attention to is the required amount of material. It often happens that, having estimated the necessary square by eye, the novice toner gets into a mess. To prevent this from happening, you need to make accurate calculations of the required material.

Let's start by measuring the area of \u200b\u200bthe glazing to be tinted. To do this, you can use an ordinary tape measure. For those who first decided to master this business, you need to make some reserve in case of unforeseen circumstances.

So for front-wheel drive cars of the VAZ family, 3 sq. m. excluding the windshield. For tinting classic Zhiguli models, 2.8 - 3 sq.m. will be enough.

Tools

The second, no less important stage of the presented event is the choice of a working tool. In this case, it is difficult to overestimate the importance of even the seemingly insignificant rig.

At the same time, a solid approach will contribute to the successful implementation of the task. What is required for this?

Water spray

First of all, you need to take care of purchasing a water spray. It is worth saying that an ordinary household spray gun is quite suitable for these purposes, meeting one single requirement - to evenly spray the solution onto the glass surface.

Liquid soap or detergent

An indispensable condition for effective film application is the treatment of the working surface with a special solution. It is usually called the setting. It is not at all necessary to buy it. Alternatively, you can use various detergents and so-called liquid soap.

With regard to soap-based solutions, it is appropriate to make some digression. The fact is that due to their composition, after their application, stains remain on the glass, which are inappropriate from an aesthetic point of view. You should also avoid using products containing alkalis. Their detrimental effect on the film can impair its adhesive properties.

Stationery knife

Another important tool is a clerical knife. It is he, by virtue of its design features, that is most suitable for cutting and trimming tint film.

Lint-free napkins

Among other things, you should stock up on cotton rags or lint-free napkins. With their help, you will have to drive out the solution remaining under the film.

Of course, you can fork out and buy a special distillation, but by and large, such a purchase is an unjustified waste of money. Napkins and cotton rags will cope with this task no worse than any distillation.

Special scraper

In this case, we are talking about a tool that allows you to perform preliminary operations for cleaning the glass surface from foreign particles. It should not be confused with special distillation, due to which the film is smoothed and excess installation solution is removed.

Building hair dryer

Well, in the role of the most expensive tool in this case, a building hair dryer acts. Its cost varies from 500 to 2500 thousand rubles. The line of the cheapest analogs includes firms from the Middle Kingdom.

There is, of course, an alternative option - under a plausible pretext to borrow a hair dryer from his wife. A household analog will do the job well.

How to properly tint the front and side windows yourself

The decisive moment has come. The tool and material have been prepared and are waiting in the wings. It's time to start the very process of toning.

The initial action at this stage is to make a pattern for the glass to be glued. In this case, one should not adhere to strictly verified dimensions. You need to leave a small allowance.

After that, the pattern should be applied to the glass pre-treated with a solution. It should be remembered that the protective layer must look outward.

The sequence of further actions is as follows:

• bring the lower end of the pattern to the lower sealing elastic of the glass, while leaving an overlap of about 1-1.5 cm;
• fit the pattern along the vertical racks with the same overlap;
• bend the lower end of the workpiece, fixing it on the upper edge of the sealing gum;
• make the required horizontal cut;
• adjust the pattern to the size of the glass.

In order to avoid cuts in the sealant when adjusting the pattern, it is necessary to apply the aforementioned forcing. It is usually placed against the elastic, which negates the risk of damage to the seal.

Pasting rear windows

Pasting the rear window is more laborious than all the others. Nevertheless, a beginner in this business can cope with this task. The pasting technology is somewhat different from the previously mentioned one.

Its algorithm includes the following actions:

• applying the solution in the middle of the glass to the glass with a sponge in the form of the letter "H";
• laying the film on glass, with its adhesive surface facing outward;
• trimming excess film (in this case, the allowance should be more than 1.5-2 cm);
• applying a blank (at this stage it is important to ensure that there are no horizontal folds on the film);
• smoothing the pattern in both planes;
• removing wrinkles with a hair dryer;
• application of the setting solution;
• reapplication of the film;
• smoothing the film.

It should be remembered that it is necessary to smooth the film evenly, starting from the center of the glass and ending with its edges. In this case, you should not allow jerks and apply great effort to the film.

Problems and solutions

In the process of pasting, especially for the first time, there are often a number of problems that can take you by surprise. To prevent this from happening, it is important to promptly and correctly respond to them and make the only correct decision.

What undesirable phenomena take place when toning a car?

Air bubbles

It happens that in the process of unscrupulous toning of the car, bubbles filled with air remain under the film. In this situation, at least two methods can be adopted. It is advisable to resort to the first in the case when the film has been pasted quite recently.

For the second method, this aspect is not decisive. So, in the first case, you should arm yourself with a plastic card or a construction eraser. Its essence is as follows: you need to smoothly press on the glass in an unfortunate place and try to squeeze the bubble outward, driving it to the edge of the glass.

Option number 2 involves the use of a building hair dryer. It completely copies the previous method with one only deviation - the squeezing out of the bubble is accompanied by local heating of the film.

Creases

Let's talk about creases and how to deal with them. When stored carelessly, tint film often loses its original appearance. Characteristic “wrinkles” or creases appear on its surface.

To get rid of them, it is enough to immerse the film in warm water. After a few minutes, it must be spread out on a smooth surface and straightened.

Stripes

Sometimes very unpleasant phenomena are observed on the tint film - streaks and streaks. The reason for this may be a poor quality coating. In this case, there is only one way out - to paste over the glass again.

In some cases, this phenomenon was eliminated by thoroughly cleaning the tinting with detergents. Still, the likelihood that this will help is extremely small.

Points

In addition to streaks, dots, most often white, may appear on the film surface. The nature of their appearance is very commonplace - dust particles, ash from cigarettes, etc.

It is not possible to get rid of such a misunderstanding. In order not to face such a problem, you should more carefully approach the issue of maintaining cleanliness while toning your car.

How car windows are tinted in other countries

What about toning in other countries? Here are some examples. So, in England and in most of European countries, the same standards and requirements for toning apply as we do.

In America, in California in particular, tinting is included in the list of mandatory options for any car.

This is explained by the fact that if there is toning, the driver will use the air conditioner less often. This will help reduce fuel consumption and reduce harmful emissions into the environment.

The practice of tinting automotive glass has many more reasons than trying to reduce the light transmittance of glass. But before the car windows are tinted with their own hands, the question of the reasons should be answered.

This will help you choose the appropriate tinting method, do it cost-effectively and efficiently.

What does a car owner need to know about tinting?

Most new cars have a so-called factory tinting... Car manufacturers, in caring for their customers, provide light tinted glass to protect against excessive sunlight. This method not only ensures safety while driving, but also does not allow violating tinting law.

To protect the interior from prying eyes, curtains for the car are additionally used instead of tinting. It is also not prohibited for the rear window of a passenger car ( with side mirrors) and for the side windows of minibuses or minivans.

Another of the old government regulations is related to windshield tinting. Determined that front glass tinting in accordance with GOST in this case, no more than 25% of the area is allowed.

It must be remembered that the permitted level of permissible shading of glasses for domestic conditions is:

1. For windshield - light transmittance not less than 70%. In this case, a stronger darkening is suitable if the film is placed in the upper part of the glass with a width of no more than 140 mm.
2. Tinted front side windows in accordance with GOST - light transmittance not less than 70%. The exception is any colored films that, regardless of the degree of light transmission, cannot be used.
3. For rear window. There are no restrictions. High intensity rear window tint is equivalent to the use of curtains. Installation of two side mirrors is required.

Another severe limitation is the prohibition of the use of reflective ( read mirror) surface. Such cars have practically disappeared from the roads lately.

If in doubt about the permitted indicators in neighboring countries, it should be borne in mind that all rules have been adjusted to the conditions of the Eurasian Economic Union, therefore, they should not differ from the similar conditions of all member countries of the Union.

Penalty for violation

Proposals to toughen liability for violation of toning rules are heard annually. But at the beginning of 2018, in response to the question, what is the fine for toning, no changes occurred with violations. Article 12.5 ( h. 3.1) involves a fine of 500 rubles. In addition, if the established standards are exceeded, difficulties will arise when passing a periodic technical inspection.

As a toughening up for violation of the rules, it is expected to raise the level of administrative action to 1.5 thousand rubles.

As an alternative to non-payment of the fine, it is proposed to eliminate the tinting "in place". If for conventional films this is theoretically possible, then for modern methods, the elimination of tinting will mean the replacement of glasses.

Therefore, you should still take into account the established norms if the car will regularly participate in road traffic. An oversight will cost more than other mistakes if the owner did not take into account what the permitted windshield tinting is.

Checking the correctness of the installed tinting

The car owner must know that the traffic police inspector must check the legality of the applied tinting, and not approve unfoundedly. The driver has the right to demand to indicate to the document, which indicates which tint is allowed on the front windows or on other elements. Already at this stage, many claims are eliminated.

To measure the degree of transmission of glasses, appropriate devices are used that have been verified and approved for measurements with an appropriate certificate. In practice, devices are used:

• "Blik" ( for glasses up to 7.5 mm);
• "Blik +" ( for thick glasses);
• "Light";
• "Tonic".

Additionally, the employee must confirm his qualifications for taking measurements. Among the main conditions for conducting research are:

1. Ambient temperature: from + 15 ° С to + 25 ° С.
2. Air humidity- from 40 to 80%.
3. Glass condition - clean dry surface.
4. Atmosphere pressure - 86-106 kPa.

You should also pay attention to the indicated measurement error indicated in the documents for the device. If the requirements are not met, measurements cannot be taken.

In the event of their illegal registration, the car owner has the right to indicate in the protocol all violations of existing methods. When analyzing an offense, the very fact of violation of the rules of tinting should not be recognized as established.

Do-it-yourself car rear window tinting. Video:

All types of car window tinting

When considering different shading options, the focus is on visual appeal and comfort for drivers and passengers. In this case, the best fit. But all modern options for applying such coatings should be considered.

Depending on the materials of execution, coating technologies, the following types of tinting are distinguished:

• protective elements on a removable base;
• using silicone materials;
• gel tinting;
• combined application method;
• electronic spraying.

When determining the method, one should take into account the area of \u200b\u200btinting application, the possibility for independent use, the advantages and disadvantages of each method.

Evolution and features of tinting methods

Regardless of the tinting method, the car owner gets some advantages when using such a car:

• protection of the inner space from prying eyes;
• reduction of heating of air and coatings in the cabin;
• reduced glare from bright sunlight.

The most affordable is the tinting method using film coatings... This method remains the oldest in terms of time of use among car owners.

The special film for car window tinting is easy to apply and dismantle when following the sequence of operations, which is why the method is often used by individual owners.

Removable toning

The current trend emerged as an alternative to film coatings. Tinting is made in the form of piece elements with a reliable and quick-release fastening.

While maintaining all the advantages of classic tinting, such as protection from prying eyes and sunlight, the artificial element will not make you incur significant additional installation costs. In addition, the coating can be easily dismantled if it is unnecessary or in case of claims. The only difficulty will be the inconvenience of storing the removed items, especially for compact cars.

Stick-on quick-fit screens are available as a variety of quick-install screens. These coatings adhere quite reliably along the glass contour.

But in the case of temperature deformations, the problem with opening and closing glasses arises on an unsecured surface.

An additional argument for such coatings is their compliance with the requirements of the Road Traffic Regulations.

Film tinting

Despite the apparent simplicity, the method allows you to endow the car with individuality due to the variety of materials. Among the known coatings are:

1. A film called "Infinity". The sample consists of several layers of low thickness with the possible application of a top layer of the "metallic" class. In this case, the film will be included in the category of "mirror tinting".
2. Transitional color coating. Usually, only the upper part is made metallized, including painted in body color. The lower half remains darkened transparent.
3. Film with a carbon-look option. The absence of metallic impurities makes the film resistant to fading and prevents glare in bright light.
4. Colored films. This group includes numerous monochromatic films of any shade, as well as “chameleon” films. In addition, it is easy to personalize the coating by using colored elements other than the main color of the film.

The group of colored films includes and athermal tinted windshield, the main purpose of which is to protect the passenger compartment from heating. If you ask yourself when a purple tinted windshield is used, then this is just a case of protecting the interior from overheating.

The benefits of silicone tinting

For all its popularity, film shading is subject to wear and tear due to the action of external sources. Scratches and scuffs also occur under the influence of time. In addition, the slightest inaccuracy during application will lead to the appearance of bubbles, folds, distortions.

More advantageous in this regard is the tinting based on fastening on silicone layer... This feature makes it easy to repeat any complex glass profile. As a consequence, the penetration of bubbles between the two coatings or the appearance of wrinkles is eliminated.

Before choosing which tinting of the side windows or the rear element is more suitable, you should consider the additional advantages of the gel method:

1. Resistant to temperature changes. The range is sufficient for domestic conditions - from +50 ° С to -50 ° С.
2. Resistance to aggressive environmental influences. Scratches, abrasions occur on the coating much less frequently.
3. High quality and natural layer. Upon examination, the coating cannot be distinguished from the factory application.
4. Ease of application. The technology assumes ease of installation of the tinted canvas, so self-application is most accessible here.
5. Physical properties. Along with a decrease in light transmission, the coating does not refract the natural layer, retains the clarity and naturalness of the picture.

If it is necessary to dismantle the installed coating, it is not difficult to completely remove the tinting. Due to the simplicity of the method and its availability, the popularity of gel tinting remains high.

Electronic tinting

The greatest concern for car owners is the problem of how to avoid punishment for violation of established standards, and what should be the tinting of the front side windows in accordance with GOST. It is on these elements and on the windshield that traffic police officers pay close attention. After all, the difficulty of obtaining information from the road and through the side mirrors is the cause of many road accidents.

An innovative technology known as electrical toning, assumes a different way of changing the light transmission of glasses. It is based on the application of a special electrochemical composition to the surface. Subsequently, depending on the level of outdoor lighting, the transparency of the glasses varies differentially.

First of all, the negative experience of using tinted glasses disappears.

In the dark, the glasses remain completely transparent, and in bright light they trap bright sunlight in proportion to the level of illumination.

The popular one has another variety. Polymer films based on liquid crystals have been developed and used. With the passage of an electric current, the structure changes, and with this the light transmittance of the surface. The name of such tinting for car owners is "monochrome" or automatic tinting.

The noted modern methods have car tinting cost an order of magnitude more, and are applied using professional equipment. However, this approach not only ensures safety when driving on the roads, but also does not raise questions from representatives of the traffic police.

Electronization. Video:

Review of price proposals for tinting

When considering price proposals for tinting, it should be borne in mind that the cost depends on the area of \u200b\u200bthe car's glazing, the coating on the entire car or only on individual glazed elements.

The most affordable option is the application of a conventional film, metallized or colored. For an average station wagon, the cost will fluctuate in the range of 6-7 thousand rubles.

In this case, the cost of a roll of a certain type of film starts at 30 rubles. per running meter.

Given the prevalence of self-installation of gel tinting, the cost of one roll of material should be considered. We calculate the need for material on our own. The average price per roll is in the range of 3-3.5 thousand rubles.

Electronic tinting using SPD technology is estimated at up to 350 thousand rubles. , and similar in quality "monochrome" tinting will cost 60-100 thousand rubles. for the entire volume, depending on the car.

DIY tinting installation

Given the complex of positive properties and the availability for self-application, many car owners are interested in the independent installation of removable tinting. Taking into account the different bulges and sizes of glasses, there is a difference between applying a film to the side surfaces and how to glue tinting on the rear window.

Before starting the film application process, it is worth thoroughly cleaning the glass surface. Do this from the inside and outside. This will help not only to lay the surface with a good adhesion coefficient, but also to see all the flaws on the back side. When cleaning, use successively detergents and an alcohol-based liquid to degrease the surface.

When planning to apply the film from the roll, you will not need to remove the glasses. When purchasing gel tinting, it is more convenient to purchase ready-made cut elements. Otherwise, the dismantling of the glasses cannot be avoided. Another available option for preparing for the application of gel tinting is to contact special cutting shops. Here, for a small fee, cutting will be carried out according to standard patterns.

Work execution algorithm

We will consider the procedure for performing the work for the method of coating without dismantling the glasses. After thorough cleaning of the surface, further work is carried out in the following sequence:

1. The tint film is applied between the seals. The distance from the edge of the sliding glasses should not exceed 2 mm.
2. When applying the film to a wet surface from the center to the edges, distillation of liquid residues is carried out. At the same time, the film is leveled over the entire surface area.
3. At the final stage, natural drying is carried out for 1-2 hours.

You should not start doing the work alone. This will not allow you to correctly orient the material. Extra hands never hurt. Also, take care in advance of the normal level of lighting and the availability of the required minimum of tools.

Tinting removal procedure

Among the typical reasons for refusing tinting, most often car owners name the following provisions:

• the presence of external damage to the coating;
• uncomfortable sensations when driving a vehicle;
• non-compliance with established standards;
• when selling a car in the secondary market.

In the case of upcoming work, the main problem is how to remove the tint from the glass yourself. Least of all labor will have to be done in the case of dismantling the gel tinting. Just pick up the edge of such a coating, and the film will pull off in just a few tens of seconds.

Another assistant in the matter of dismantling the tint film will be a regular hair dryer ( or iron) with a good power reserve. The main task will be to increase the surface temperature due to hot air or steam to a temperature of no more than 40 ° C. In the future, it remains only to remove the remnants of the glue on the glass.

Thus, the process of darkening car windows, on the one hand, is associated with tangible benefits in terms of comfort. On the other hand, a balanced approach is required when choosing a tinting method. This is due to financial costs, safety issues and the convenience in the subsequent operation of the applied coating.

The habit of toning the car to "zero" is a thing of the past. And even if tinting is just a way to stand out in the stream, this issue should be approached carefully.

Every car owner wants his car to look solid and be as comfortable as possible. One of the types of tuning that is resorted to in this case is glass tinting. In this article, we will learn about the main aspects of such an upgrade.

Pros and cons of window tinting Choosing a film for tinting Car window tinting with your own hands Materials and toolsPreparatory stageTinting process Useful tips $ (".index-post.contents"). ToggleClass ("hide-text", localStorage.getItem ("hide-contents" ) \u003d\u003d\u003d "1")

Pros and cons of window tinting

Consider the main advantages of tuning:

in the heat, the interior is less susceptible to heating; the upholstery material does not fade; plastic interior products do not overheat and do not lose their appearance; presentable appearance of the car; both passengers and things left in a closed car are hidden from prying eyes; the driver's eyes are less affected by the blinding rays of the sun or oncoming headlights, the light coming from the back of the car; in the event of a collision, the glass will not crumble, but will remain tinted.

Disadvantages:

the view is reduced, especially at night, which makes parking difficult and can create an emergency; in the flow of a large amount of transport, the mirror ability of the film will blind other drivers; too high density of tinting layers can cause window regulators to break down; non-compliance with state standards is the cause of fines.

Did you know? In China, tint film with the image of a famous character (singer, actor) is popular.

The choice of film for toning

There is a large selection of tint films on the market today. To figure out which film to give preference to, let's consider it according to several criteria.

Cost and quality:

The leaders in the production of this material are the American companies LLumar, 3M, SunTek, SolarGard. The quality is undeniable, which affects the price. The 3M company (USA) offers a budget version of the product; the line includes such films as Black Shade, Metallic Shade. The quality is not inferior, but the price is several times lower. The Chinese manufacturer offers the cheapest products, but they quickly fade and lose their external gloss.

By destination:

Sunscreen (ultraviolet and infrared radiation). Impact resistant (consists of more layers). Decorative (emphasizes the individuality of the car owner).

Manufacturing method:

Non-metallized - polymer, acrylic and painted layer. Affordable, does not create problems in the operation of mobile and navigation systems, there is no mirror effect. Does not last long. Metallized - in addition to the main layers, it contains metallized. Has a mirroring effect, lasts longer and protects against ultraviolet radiation more effectively. May interfere with mobile communications and navigation systems.

In addition to the above criteria, it is important to consider the ability of the film to transmit light.

Learn about removable, silicone, electronic, chameleon tinting; front glass tinting according to GOST; toning, which the device "does not see".

Light transmission options:

5% - the interior is not visible from the outside; 10% - the outlines of people in the cabin are noticeable; 15% - silhouettes are clearly visible; 20% - you can see faces from the outside; 35% - by looking closely, you can see the entire interior; 50% - even small details inside the car are visible ...

After considering all the criteria and determining the toning function, it will not be difficult to make the final choice.

Did you know? According to the world statistics of the study of road accidents, tinted cars are less likely to be their participants. This is explained by the fact that drivers are not distracted by studying those sitting in neighboring or oncoming vehicles, but are entirely focused on the road.

Do-it-yourself car window tinting

Car tinting at home is not difficult. In this case, the main thing is accuracy and adherence to the rules of work.

Materials and tools

Materials and tools required for work:

film; sponge; utility knife with a wide blade; spray; water and detergent; plastic spatula; sharp knife for cutting material; hair dryer.

Learn how to remove old tinting and how to wipe off the glue from the tinting.

Preparatory stage

Let's prepare the work surface:

Pour water with a few drops of detergent into a spray bottle and shake. Spray the compound onto your work surface.

First, go over the hard side of the sponge.

Then, with a utility knife blade, go over the entire glass, especially carefully - in the corners where the most dust collects.

Wash off again with detergent.

Important! Before work, you should clean the glass as thoroughly as possible, since any speck can create a bubble.

Open the roll of the selected material, place it on the outside of the dampened glass and, leaving about 2 cm at the edges, cut it off.

When making a pattern, leave 1 cm of film at the bottom (under the lash) and a few millimeters along the rest of the edges to avoid a gap. The top needs to be trimmed to fit the edging.

Cut the pattern carefully with a sharp knife. Cut off the top first, then the sides.

Make sure there are no gaps by looking at the work from the inside. Now lift the glass and cut the bottom edge. The pattern is ready.

Tinting process

We proceed directly to pasting:

Rinse the work surface with a spray bottle and go over it with a spatula. Rinse again.

After removing the unnecessary layer, generously moisten the work surface and glass surface. Take the film by the edges and attach it to the glass, moisten.

Spread the material very neatly left and right, paying particular attention to the edges.

Check how the tinting looks from the outside. If there are no bubbles, dry everything with a hairdryer. The work is done.

Useful Tips

Experts recommend using Johnsons Baby shampoo: this product provides the easiest film glide possible. Try to cut the edging with one movement of your hand, without lifting the knife. This will give the most accurate result, without any torn edges. Moisten the glass regularly - material and surface should be in close contact. Higher quality and easier to work with is a film made in the USA. Chinese film is very thin and is very likely to be scratched or creased. The American material is denser, peels off easily and is easily tucked in along the edges. Moreover, it is more elastic. For beginners, it is better to remove the eyelash before work to avoid creases. Please note that a completely closed glass goes a little into the seal, so the glass must be lowered from above. Smooth the film sideways, never up and down. Make sure that all air and liquid is removed. If the film has slipped a little, you can correct it by pulling it in the right direction while it is still wet. Always leave a margin on the edges, do not overdo it so that wrinkles do not appear later. When working with a spatula, you need to be extremely careful and not press it into the material, so as not to scratch it.

In more detail, the tinting process can be viewed in the following video:

So, the process of tinting a car can be done at home, while saving on payment at a car dealership. This procedure is simple and requires only care, accuracy and accurate calculations. However, before traveling abroad in your car, you must carefully study the rules and laws adopted regarding tinting.