The car manufacturer notes that replacing the cabin filter Nissan Qashqai must be performed every 30,000 kilometers or every two years (whichever comes first). But in the conditions of Russia, nothing will remain from the filter in two years, so it has to be changed more often. A dirty filter is a source of unpleasant odors. It also leads to a decrease in the efficiency of the interior heater. Owner reviews indicate that it is advisable to change the filter for Nissan Qashqai in Russia every six months.
The original Nissan Qashqai cabin filter is designated code 27277 - EN000. The manufacturer also offers a similar element marked 27277 - EN025. Finding a cabin filter for this crossover will not be difficult, since the car is quite popular in our market. Analogs from third-party companies are also on sale. Recall that a similar element is used on Nissan x-trail T31.
Preparation
To complete the work we need:
- screwdrivers (slotted and Phillips);
- lantern;
- new filter element;
- patience…
You will definitely need the latter, since everything is not so easy to do, compared to other cars. So let's get started!
Replacement procedure step by step
1. First you need to dismantle the protective cover of the floor tunnel from the driver's side, it is made of plastic. To do this, we pull it towards ourselves.
The cover is attached with 4 latches, a guide is also used. First, we release the latches, after which we shift the plastic to the right (details in the photo).
2. The next step is to prepare the temperature damper control module (yellow star in the photo). Airflow should be directed to windshield and turn on the maximum temperature (position “HI”). This will move the damper to the upper extreme position (the yellow arrow in the photo indicates the damper drive wheel). Another option is to move the damper to the lower extreme position, for which we turn on the temperature in the “LO” mode. Next, we dismantle the cabin filter plug. The lower half of the plug is folded back with a slotted screwdriver (red arrow in the photo).
3. There is a latch at the top of the plug; it is quite easy to remove the element.
Before us opens the place for installing the cabin filter.
4. At this stage, it will not be possible to pull out the filter, since the stove damper control module interferes. This element should be disconnected. Disconnect the chip from the corresponding connector of the control module and unscrew a couple of mounting bolts. Uninstalling the module is quite simple. Make sure the choke control wheel only moves in one direction.
5. After dismantling the block, the filter rests on the electronic accelerator pedal control module. Some motorists may come to the conclusion that they will have to remove the pedal assembly (some owners are accustomed to performing this procedure without fail). But in reality, you just need to bend the filter and pull it out, since we will throw it away anyway.
6. In the photo you can see how the original filter element looks on a car with 20,000 km on the speedometer. As you can see, it is imperative to change it, although it managed to pass only 2/3 of the recommended resource. By the way, the filter has arrows indicating the direction of air flow.
A similar mark is also present on the purchased cabin filter.
7. To install the filter, twist it in the form of a butterfly or figure eight. Check the direction of the air, the arrow must point to the passenger compartment. Interestingly, installing a new element is much easier than removing an old filter element. After that, the stove damper control module is connected. Before that, return the flap drive wheel to its original position and install the control unit, holding the wheel with a screwdriver. You can screw the block using a thin long screwdriver or an L-shaped tool.
10. We connect the electronic connector of the damper position control module and test the element for operability. We start the engine and select on the console different operating modes of the air conditioner (from minimum to maximum). The wheel should turn without any problem.
11. The final touch is the installation of the floor tunnel lining.
What is the task of a cabin filter installed in a car? Naturally, it is responsible for air purification and serves as a dust collector. But in order for the air to enter the cabin fresh and clean, the cabin filter must be changed periodically. If we look at books on technical operation this or that car, in particular the manual car nissan Qashqai, you can see the following. Manufacturing plant regulations for maintenance, the replacement of the cabin filter obliges to carry out every 30 thousand kilometers. But given russian conditions operation, the replacement procedure should be carried out at least twice a year, and even better - with each arrival of a new season, be it summer or winter.
How do you know when it's time to change the filter?
If, after buying a car and operating it, an unpleasant foreign smell is felt in the car's interior, then this is the first sign that replacing the Nissan Qashqai cabin filter is mandatory, since it does not work at full capacity. And if the airflow is not good enough in the car, or dust that has firmly settled in the cabin flies, then these are sure signs that the filter has become unusable. It is worth noting that some drivers also complain about the poor performance of the stove, this should also be taken into account.
Although the procedure for replacing the cabin filter is not as simple as it might seem at first glance, the car owner can do it on his own. Replacing the filter does not require special, complex tools. All you need is a Phillips and slotted screwdrivers, a pair of cotton gloves, a small LED flashlight, and, of course, a brand new filter itself.
It is best to select an original filter from the manufacturer for a replacement, but an analogue suitable for the design of the car and produced by a good company is also suitable.
Filter replacement procedure
Since the filter itself is located on the driver's side, the first step is to put the driver's seat in order. That is, remove the dirt and put some kind of rags on the bottom so as not to stain the clothes. If everything is done in accordance with the points listed below, then the entire replacement process will not take much time and should go without delay.
- The control unit itself will have to be dismantled, as it will interfere with replacing the old filter. To do this, unscrew it with a Phillips screwdriver. After removing the block, it is imperative to check the flap control wheel.
- Now you can remove the filter cover itself. There should be no problems here, it snaps off easily. Prying with a slotted screwdriver, it will easily fall out of the grooves.
- Using the same slotted screwdriver, you need to pry the old cabin filter and pull it out of its slot. When removing the old filter, its folds and creases are permissible, it will still have to be thrown away. The old filter is a pitiful sight compared to the new one. Flakes of dust hanging from all the grooves not only give an unpleasant odor, they are also harmful to health. Therefore, after replacing the filter with your own hands, you can make sure that you need to change it on time, and not breathe in those flakes of dust and dirt that clog all its sinuses.
- Further, the new filter must be folded like a butterfly, or an accordion, that is, fold into fold. And only then it can be installed, which will be much easier than when removing the old one.
- After installation, you need to properly reassemble everything - while observing the sequence with which the cabin filter was removed. Replace the filter cover first. After that, the damper control unit is installed back, and after its installation, the plastic facing plate.
- At this point, the process of installing a new cabin filter can be considered successfully completed. As soon as the car owner starts operating the car and the new filter starts working at full capacity, only then it will be possible to feel the difference between what the driver and passengers breathed before the replacement, and what they breathe after it. Plus, many Nissan Qashqai car owners, after replacing the filter, also note improved operation of the stove.
Video
In addition, we suggest watching a short video explanation.
Russian car owners are well aware of the model of the Japanese salon crossover NISSAN QASHQAI. A lot of drivers sitting at the wheel are worried about odors that periodically penetrate into the passenger compartment.
All of this is due to the fact that the cabin filter installed on board the car gets dirty from time to time. Also:
- foreign odors get inside the car;
- the quality operation of the system, which circulates air masses inside the car's cabin, is disrupted.
A dirty pollen filter forces the air conditioning system as well as the heating system to work in an increased mode. The latter wear out much faster. Fuel is consumed in large volumes, the components are more likely to break. If you do not replace the worn-out Nissan Qashqai cabin filter in time, you will soon have to change the entire system.
In broken cabin filters harmful chemicals and bacteria accumulate, mold develops, which is very difficult to get rid of. The presence of mold and harmful impurities in the cabin is the cause of allergic diseases.
The time to change the cabin filter is determined by the degree of contamination of the filter itself. It is not uncommon for the filter to become clogged long before the scheduled date. Taking advantage of detailed instructions, we can do the installation by ourselves.
To replace the cabin filter, we need keys with heads of different calibers, as well as a set of screwdrivers.
Instructions: how to change the cabin filter on a Nissan Qashqai with your own hands + photos and videos
The process is carried out in the following sequence.
1. Remove the decorative plastic panel (it just snaps off).
Replacing the cabin filter Nissan Qashqai
2. To do this, direct the airflow to windshield, and set the temperature to maximum (the damper is in the extreme top position). As a result of this operation, the flap will be positioned so that it becomes easy to get to it.
3.Using a flat screwdriver, remove the filter chamber plug.
4. Since removing the filter will interfere with the damper control unit, first dismantle this unit using a screwdriver. To do this, remove the chip from the connector of the control unit, and then unscrew the two bolts holding the unit.
5. We take out the old filter and replace it with a new one. Pay attention to the direction of the arrow, it should match how the previous filter was installed.
6.Close the lid, install the adjustment unit back.
7.Prepare to the place decorative panelthat is under the steering wheel.
At the end of the operation, passengers will begin to breathe freely, and car stove will work much better.
Also watch the video
